Call (703) 880-8400

GPR Concrete Scanning

Know exactly what is inside the slab before you cut, drill, or anchor. Our licensed GPR operators scan and mark your concrete in real time so your crew can work with confidence.

Real-time marking Locates rebar & PT cable Scans up to 24" Same-day report Licensed operators
Call (703) 880-8400
Plan the whole job GPR Scanningthen Core Drillingthen Concrete Repair

What Is GPR Scanning?

Ground penetrating radar (GPR) is a non-destructive method that uses high-frequency radio waves to image the inside of concrete slabs, walls, and structural elements in real time. You see exactly what is embedded before you cut, drill, or anchor.

The GPR unit sends electromagnetic pulses into the material and records the reflected signals, producing a real-time cross-section of everything inside. On a single scan we locate:

  • Rebar mats and wire mesh
  • Post-tension cables
  • Electrical conduits and PVC pipes
  • Radiant heat tubing
  • Voids and changes in slab thickness

GPR scanning is standard practice before any concrete cutting, core drilling, or anchor installation on commercial projects throughout Fairfax County, Loudoun County, Arlington, and the greater DMV. Hitting a post-tension cable can compromise structural integrity and trigger expensive engineering reviews. Cutting into a live electrical conduit creates immediate safety hazards and schedule delays. A scan takes minutes per location and eliminates these risks before your crew starts work.

OTM provides GPR scanning as a standalone service or bundled with our core drilling and saw cutting crews. When you book GPR with cutting, we scan, mark, and cut in a single mobilization. No waiting for a separate scanning contractor. No scheduling gaps. Your project stays on track.

When Do You Need GPR Scanning?

If your project involves cutting, drilling, or anchoring into existing concrete, GPR scanning should be your first step. Here are the most common situations where general contractors in Northern Virginia, DC, and Maryland call us:

Before Core Drilling

Locate rebar spacing, post-tension cables, and embedded conduits before drilling plumbing, HVAC, or electrical penetrations. Required on most commercial renovation and tenant build-out projects in Arlington and Washington DC.

Before Saw Cutting

Map what is inside the slab before cutting expansion joints, trenches, or openings. Especially critical on post-tensioned parking structures and elevated decks common in Fairfax County and Tysons commercial developments.

Anchor and Embed Installations

Verify clear zones for anchor bolts, dowels, and structural embeds. Avoid hitting reinforcement that would compromise the connection or the slab. Common on steel erection and curtain wall projects.

Post-Tension Cable Locating

PT cables are under extreme tension and cannot be cut. GPR maps their exact path and depth so your crew can plan penetrations safely. We scan PT structures across Montgomery County, Prince George's County, and the entire DMV.

MEP Rough-In Coordination

Mechanical, electrical, and plumbing contractors use our scans to plan routing through existing slabs without conflicts. Reduces RFIs and field clashes on renovation projects.

Structural Investigation

Verify rebar placement, measure slab thickness, and locate voids or delamination for structural engineers. We support condition assessments on aging buildings and parking structures across the Loudoun County data center corridor and Prince William County commercial zones.

How It Works

Four steps from call to clear-to-cut.

1

Site Assessment

You tell us what you need scanned and where. We review your drawings, confirm slab type and thickness if known, and select the right antenna frequency for the job. We can typically mobilize within 24 to 48 hours.

2

Scan Execution

Our operator runs the GPR unit across the target area in a systematic grid pattern. Multiple passes at different orientations ensure full coverage. We scan floors, walls, ceilings, columns, and beams as needed.

3

Real-Time Marking

As we scan, we mark the location of rebar, conduits, cables, and other embedded objects directly on the concrete surface. Your crew can see exactly where it is safe to cut or drill. We use color-coded markings to distinguish between different types of targets.

4

Report Delivery

After scanning, we provide a detailed report with images, target depths, and findings. Reports include annotated scan images and a summary of all identified objects. Digital copies are emailed the same day for your project records.

Our GPR Equipment

Professional-grade units built for commercial concrete scanning.

GSSI StructureScan Mini XT

Our primary concrete scanning unit. The StructureScan Mini XT is the industry standard for structural concrete inspection. It features a 1600 MHz antenna optimized for concrete, real-time 2D and 3D imaging, and depth penetration up to 24 inches. Built-in data collection for detailed post-scan analysis and reporting.

GSSI StructureScan Pro

For complex or large-scale scanning projects. The StructureScan Pro provides higher resolution imaging with dual-frequency capability, allowing us to scan at multiple depth ranges in a single pass. Ideal for heavily reinforced slabs, post-tensioned structures, and situations requiring detailed mapping of congested rebar layouts.

Handheld Palm XT

A compact, single-hand GPR unit designed for quick spot checks and tight spaces. Perfect for scanning around columns, inside elevator shafts, on walls, and in areas where the larger cart-based units cannot reach. Provides immediate go/no-go results for individual penetration locations.

Support Equipment

We carry all necessary support gear on every mobilization, including marking paint and crayons for surface marking, measuring wheels and laser distance meters for precise positioning, tablets for on-site report generation, and reference charts for identifying target types by signal response.

GPR Scanning vs. Concrete X-Ray

Both GPR and X-ray can image the inside of concrete, but they work very differently. Here is how they compare for commercial construction applications:

GPR Scanning Concrete X-Ray
Access required One side only Both sides of the slab
Safety No radiation, no site clearing Requires radiation safety zone and licensed technician
Speed Real-time results, scan and mark in minutes Film development required, results in hours
Large area scanning Covers large areas quickly with grid passes One shot per exposure, slow for large areas
Depth range Up to 24 inches in most concrete Up to 18 inches depending on density
Cost Lower per-scan cost, no safety setup overhead Higher due to radiation safety requirements
Best for Pre-cut/drill scanning, rebar mapping, PT cable locating, structural surveys Situations requiring high-resolution imaging of a single specific location

For most commercial concrete cutting and drilling work in the DMV, GPR is the faster, safer, and more cost-effective choice. X-ray still has its place for highly detailed single-point imaging, but the vast majority of pre-cut scanning on job sites across Northern Virginia, DC, and Maryland is done with GPR.

GPR Scanning Cost

GPR scanning pricing depends on the scope of work, number of scan locations, and site conditions. Here is a general guide for commercial projects in Northern Virginia, DC, and Maryland:

Single Location

A few penetration spots

  • 1-3 scan areas on the same floor or slab
  • Real-time surface marking
  • Same-day digital report
  • Ideal for a few penetration locations

Full-Day / Large Scope

Multi-floor mapping

  • Extensive scanning across multiple floors or buildings
  • Full rebar and PT cable mapping
  • Engineering-grade deliverables
  • Multi-day projects quoted individually

Pricing varies by project complexity, slab thickness, congestion of reinforcement, and site access conditions. Bundle GPR scanning with core drilling or saw cutting and save on mobilization costs. Call (703) 880-8400 for a project-specific quote.

One crew scans, marks, and cuts on the same visit.

You are not waiting days for a separate scanning sub. One call, one mobilization, and a marked slab with a report in your inbox the same day.

Scan and cut, same day

We also core and saw cut, so we scan, mark, and cut in one mobilization with no scheduling gaps.

Licensed and insured

VA Class A license, $2M general liability, and full workers' comp so your site stays compliant.

Same-day scan reports

Annotated images, target depths, and findings emailed the day we scan, ready for your RFI responses.

Full DMV coverage

Equipment staged and ready across Northern Virginia, DC, and Maryland for fast mobilization.

24"
Scan depth
Same day
Report delivery
24-48 hr
Mobilization
Class A
VA licensed & insured

GPR Scanning FAQ

Our GSSI StructureScan units can scan through concrete slabs up to 24 inches thick in most conditions. Depth accuracy depends on concrete composition, moisture content, and aggregate type. For heavily reinforced or post-tensioned structures, we use multiple antenna frequencies to get clear readings at different depths.

Yes. GPR scanning before core drilling or saw cutting is considered industry best practice and is required on many commercial projects. Hitting a post-tension cable can cause structural damage, costly repairs, and serious safety hazards. A GPR scan takes minutes and can save you thousands in potential damage and project delays.

GPR can detect rebar (including depth and spacing), post-tension cables, electrical conduits, PVC and metal pipes, radiant heating lines, wire mesh, voids, and changes in slab thickness. It can also identify the location of embedded items like anchor bolts and structural steel connections.

Most individual scan areas take 15 to 30 minutes depending on the size of the area and complexity of the structure. A typical commercial project with multiple scan locations can be completed in half a day. We mark findings in real time so your crew can proceed with drilling or cutting the same day in most cases.

We scan floors, walls, ceilings, columns, and beams. Our handheld GPR units are designed for vertical and overhead scanning. This is common on renovation and tenant build-out projects where MEP penetrations need to be made through existing structural elements.

GPR scanning is quoted by the number of scan locations, slab conditions, and site access. A single-location scan is quick and priced accordingly, while half-day and full-day mobilizations covering multiple areas or full rebar and PT cable mapping are scoped to the project. Bundling GPR with core drilling or saw cutting saves on setup. Call for a project-specific quote.

GPR scanning uses radar waves and requires access to only one side of the slab. It produces real-time results with no radiation hazard. Concrete X-ray uses actual X-ray radiation, requires access to both sides, needs a safety exclusion zone, and takes longer for film development. GPR is faster, safer, and more cost-effective for most commercial scanning applications. X-ray may be preferred when very high resolution is needed at a single specific point.

Virginia building code does not explicitly require GPR scanning before concrete cutting. However, many project specifications, engineering plans, and GC safety programs mandate non-destructive scanning before any penetration in post-tensioned or structurally reinforced concrete. OSHA guidelines also require employers to identify embedded hazards before cutting or drilling. In practice, GPR scanning is considered standard of care on commercial projects throughout Fairfax County, Arlington, Loudoun County, and the DC metro area.

GPR can identify areas of elevated moisture content within concrete because water changes the dielectric properties of the material and produces a different signal response. While GPR is not a dedicated moisture meter, it is effective at locating zones of trapped water, saturated fill, and active leak paths beneath slabs. For targeted leak detection, we recommend combining GPR with our pipe camera inspection service to identify the source.

We typically mobilize within 24 to 48 hours for GPR scanning projects across Northern Virginia, Washington DC, and Maryland. For urgent requests in Fairfax County, Arlington, or Prince William County, same-day service may be available depending on crew schedules. Call (703) 880-8400 to check availability for your project.

Request a GPR Scanning Quote

Tell us about your project and we will get back to you within 2 hours during business hours. Or call us directly:

(703) 880-8400
VA Class A Licensed
$2M General Liability
Same-Week Availability

Ready to Get Your Project Moving?

Call now or request a quote. We respond within 2 hours during business hours.

Call (703) 880-8400