Call (703) 880-8400

Core Drilling Services

Precision concrete core drilling from 1 to 24 inch diameters. Walls, floors and ceilings. Licensed operators with GPR pre-scan included on every job across Northern Virginia, DC and Maryland.

GPR pre-scan included 1" to 24" diameters Water-controlled, low dust Licensed operators Same-week scheduling
Call (703) 880-8400
Plan the whole job GPR Scanningthen Core Drillingthen Concrete Repair

What Is Core Drilling?

Core drilling cuts precise, circular holes through concrete, masonry, stone, and asphalt with a diamond-tipped bit. You get clean, exact openings without the cracking that impact methods cause.

It is the preferred way to make penetrations in structural concrete on commercial job sites across Fairfax County, Arlington, Loudoun County, Prince William County, Washington, DC, and the Maryland suburbs. General contractors use it for:

  • Plumbing rough-ins and pipe sleeves
  • HVAC ductwork penetrations
  • Electrical conduit runs
  • Anchor bolt installations
  • Structural testing and concrete sampling
  • Mechanical chases, from a single 2 inch hole to 18 inch openings

OTM handles the full scope with licensed operators. Every job includes a GPR pre-scan to locate rebar, post-tension cables, and utilities before the first cut, then drilling, core removal, and cleanup, so your crew moves forward without delays. We also serve Montgomery County and Prince George's County, MD.

When Do You Need Core Drilling?

If your project requires clean, round penetrations through concrete, masonry, or stone, core drilling is the right method. Here are the most common applications where general contractors across Northern Virginia, DC, and Maryland call us:

Plumbing Penetrations

Create precise holes for water supply lines, drain pipes, and fire suppression risers through concrete slabs and walls. Core drilling ensures pipe sleeves fit cleanly without oversized openings or patching. Common on renovation and tenant build-out projects in Fairfax County and Arlington.

HVAC Ductwork

Drill large-diameter openings for ductwork, exhaust runs, and mechanical chases through floors and walls. Diameters from 8 to 24 inches are standard for commercial HVAC penetrations. We handle projects from office build-outs in Washington, DC to data center work in Loudoun County.

Electrical Conduit

Core drill clean conduit pathways for power feeds, low-voltage cabling, and fiber runs. Smooth-walled holes protect wire insulation and allow easy cable pulling. Ideal for electrical upgrades and new distribution on commercial sites across Prince William County and the DMV.

Structural Testing

Extract concrete core samples for compressive strength testing, petrographic analysis, and condition assessments. Our operators drill samples to ASTM standards for engineering evaluation on aging structures and new construction throughout Montgomery County and the region.

Anchor Holes

Drill precision holes for anchor bolts, dowels, and structural embeds in concrete. Clean, round holes ensure proper bond and load transfer for steel connections, equipment mounts, and guardrail posts on commercial and industrial sites in Prince George's County and Northern Virginia.

Renovation Openings

Create openings for new stairwells, elevator shafts, mechanical chases, and pass-throughs during building renovations. Core drilling produces clean edges that reduce finishing work compared to demolition methods. We support major renovation projects across the DC metro area paired with our saw cutting services.

How It Works

Four steps from scheduling to a clean, inspected penetration.

1

GPR Scan / Locate

Before any drilling begins, we scan the work area with ground penetrating radar to map rebar, conduits, post-tension cables and embedded utilities. This prevents costly strikes and structural damage.

2

Rig Setup and Anchoring

We position the core drill rig and secure it using vacuum pads or mechanical anchors depending on the surface and orientation. The rig is leveled and aligned to your specified location and angle.

3

Precision Drilling

Our operator advances the diamond bit at controlled speed and pressure, using water suppression for dust control and bit cooling. The result is a perfectly round, smooth-walled opening at the exact diameter specified.

4

Cleanup and Inspection

We remove the concrete core, vacuum slurry and debris, and inspect the finished penetration. The area is left clean and ready for your next trade to proceed immediately.

Our Core Drilling Equipment

Professional-grade rigs and tooling for any diameter and application.

Core Drill Rigs

Hydraulic and electric rigs rated for continuous duty. Floor-mounted, wall-mounted and overhead configurations for any drilling orientation your project requires.

Diamond Bits (1" to 24")

Full inventory of diamond core bits from 1 inch through 24 inches in diameter. Segmented and continuous rim options for concrete, reinforced concrete, block, brick and stone.

Wet and Dry Drilling

Water-fed systems for standard wet drilling with full dust suppression and slurry containment. Dry drilling capability for sensitive areas near electrical panels, occupied spaces or where water is not permitted.

Core Drilling vs. Impact Methods

Core drilling is not the only way to make holes in concrete, but it is the best method for most commercial applications. Here is how it compares to hammer drilling and demolition methods:

Core Drilling Hammer Drilling Demolition / Breaker
Precision Exact diameter, tight tolerances Moderate, limited to small diameters Low, irregular openings
Finish quality Smooth, clean walls Rough interior surface Jagged edges, requires patching
Structural impact Minimal, no micro-cracking Moderate vibration stress High, can cause cracking in surrounding slab
Noise level Low to moderate High Very high
Dust control Water suppression, minimal dust Significant dust without vacuum Heavy dust and debris
Vibration Very low Moderate to high Very high
Best for Plumbing, HVAC, electrical, anchor holes, structural samples (1" to 24") Small anchor holes under 1" in non-critical areas Rough demolition where precision is not required

For commercial projects in Fairfax County, Arlington, DC, and throughout the DMV, core drilling is the standard for any penetration where precision, clean finishes, and structural integrity matter. Impact methods still have a place for rough demolition, but they are not suitable for MEP penetrations or finished work.

Core Drilling Pricing

Core drilling is quoted by hole diameter, slab thickness, reinforcement density, and site access. Here is how the work breaks down by size for commercial projects in Northern Virginia, DC, and Maryland:

Small Diameter (1"-4")

Fast, single-pass holes

  • Electrical conduit and low-voltage runs
  • Small plumbing lines and pipe sleeves
  • Anchor bolt holes
  • Concrete core samples for testing

Large Diameter (13"-24")

Large structural openings

  • Large HVAC ductwork and mechanical chases
  • Stairwell and elevator shaft openings
  • Multi-pipe penetrations
  • Structural renovation openings

Pricing varies based on slab depth, rebar density, drilling orientation (floor, wall, or ceiling), and site access. Multiple holes on the same mobilization are discounted. Bundle core drilling with GPR scanning or saw cutting and save on mobilization costs. Call (703) 880-8400 for a project-specific quote covering Loudoun County, Prince William County, Montgomery County, MD, and surrounding areas.

One crew that shows up ready and leaves it clean.

You are not managing a driller, a scanning sub, and a cleanup crew. One call, one mobilization, and one company standing behind the work.

GPR scan built in

We locate rebar, PT cable, and conduit before we drill. No surprise charge, no second mobilization.

Precision tolerances

Holes drilled to spec so your sleeves and penetrations fit the first time, without field rework.

Clean operation

Water suppression and slurry control keep adjacent trades working while we cut.

Full size range

1 to 24 inch bits and rigs on one truck, so the whole scope happens on a single visit.

1-24"
Diameter range
GPR included
On every core job
2 hr
Quote turnaround
Class A
VA licensed & insured

Core Drilling FAQ

We drill holes from 1 inch to 24 inches in diameter. Common sizes for plumbing and electrical penetrations range from 2 to 6 inches, while HVAC ductwork and structural openings typically require 8 to 24 inch cores.

Yes. Every core drilling job includes a GPR (ground penetrating radar) pre-scan at no extra charge. This locates rebar, post-tension cables, conduits and embedded utilities so we can drill safely and avoid costly damage.

We core drill through floors, walls and ceilings. Our rigs mount vertically, horizontally or overhead using vacuum anchoring or mechanical bracing, so we can drill in any orientation your project requires. Wall and ceiling penetrations are common on renovation projects across Arlington, Washington, DC, and the DMV.

Wet core drilling uses water to cool the diamond bit and suppress dust. It is the standard method for most concrete work. Dry core drilling uses no water and is used in areas where water would cause problems, such as near electrical panels or occupied spaces. We offer both methods depending on site conditions.

We typically schedule core drilling within 2 to 3 business days of your request. For urgent projects in Fairfax County, Loudoun County, or Prince William County, same-week and next-day availability may be possible depending on crew schedules. Call (703) 880-8400 for the fastest turnaround.

Core drilling is quoted by hole diameter, slab thickness, reinforcement density, and site access. Smaller holes are faster and cost less, while large-diameter and multi-pass openings take more time and tooling. Multiple holes on the same mobilization are discounted, and bundling with GPR scanning or saw cutting saves on setup. Call for a project-specific quote.

Yes. Our diamond core bits are designed to cut through reinforced concrete, including rebar mats and wire mesh. We GPR scan first to map reinforcement so we can plan the optimal drill path. For post-tensioned slabs, we locate PT cables and adjust penetration locations to avoid them entirely, since cutting a tensioned cable can cause structural damage.

Yes. Our rigs are configured for floor, wall, and ceiling drilling. For horizontal and overhead work, we use vacuum anchor pads or mechanical bracing to secure the rig. Wall and ceiling penetrations are common on renovation projects across Montgomery County, Prince George's County, and the greater DC area where new MEP routing needs to pass through existing structural elements.

A typical 4-inch hole through an 8-inch concrete slab takes 10 to 20 minutes including setup, drilling, and core removal. Larger diameters and thicker or heavily reinforced slabs take longer. Most single-location jobs with a few holes are completed in half a day, including GPR scanning, setup, drilling, and cleanup.

Most core drilling uses water to cool the diamond bit and control dust. This is called wet drilling and produces the best results for bit life and cut quality. In areas where water is not permitted, such as near live electrical panels, server rooms, or finished interiors, we use dry drilling with vacuum dust extraction. We carry equipment for both methods on every job across Northern Virginia, DC, and Maryland.

Request a Core Drilling Quote

Tell us about your project and we will get back to you within 2 hours during business hours. Or call us directly:

(703) 880-8400
VA Class A Licensed
$2M General Liability
Same-Week Availability

Ready to Schedule Core Drilling?

Call now or request a quote. We respond within 2 hours during business hours.

Call (703) 880-8400